How to program terk universal remote - Step 2: Remove the Batteries. After locating the battery cover, the next step is to remove the batteries from the universal remote. This is a crucial step in disconnecting the remote, as it effectively cuts off its power source. If your remote uses standard replaceable batteries, carefully take them out one by one.

 
Turn on your TV or another device you wish to control. Press and hold the corresponding Device and Power buttons on the remote at the same time. Wait until the power button comes on, and then release both buttons. Pointing the remote at the TV or another device, press the Power button on the remote and wait 2 seconds.. Gas prices independence missouri

There are four ways you can program the universal remote to operate your devices. Try them in the order listed. The Direct Code Entry lets you enter a code from the accompanying code list for your brand of device. The Brand Code Search searches through the codes for select brands of devices.Step-by-Step Guide to Programming a Universal Remote to a Sharp TV. Step 1: Locate your TV's code. Universal Remote Codes for Sharp TV Models. Step 2: Power on the devices. Step 3: Put the remote in programming mode. Step 4: Enter the code. Step 5: Test the code.Whether you've lost your original remote, inherited an old TV, disc player, or receiver that is missing its remote, or just want to de-clutter your living room, the Terk rechargeable 6-device universal remote is a very reasonably priced, though somewhat basic, remote control that does a lot of what it needs to without much in the way of fuss or programming difficulties.The Terk - Rechargeable 8-Device Backlit Universal Remote (model TKTC8GB) supports a wide range of brands and models of devices. I was eager to consolidate all of the devices in the family room and store the collection of remotes that live on the table. Some of those devices are admittedly getting old.Are you tired of juggling multiple remote controls just to watch your favorite TV shows? Look no further than your RCA remote control. With its universal capabilities, the RCA remo...Once you have entered the code, aim your remote control towards the television, press and hold the power button, and release if the device shuts off. Note: If you have entered an incorrect code, the LED light will blink multiple times. If that happens enter the next code on the list. 6. Going back, when your device is turned off, it is an ...It should look something like "714543-xxxx". The first six numbers remain the same; the last four are what you need to look for. If the last four digits end with "20", like "714543-8020", then your remote will accept the 4-digit code. On the other hand, if the last four digits end with "30", like "714543-8030", your Bose ...How at Programming Terk Universal Remote Are Auto Search. In who auto search method, choose that comprehensive remote encrypted are gone through scanner process are the remote. It scanner one id under one die to find out the correct remote code that works with your remote into program the control. Follow the …Follow these steps to get started with your remote control. Remove the battery compartment cover, insert the provided coin-cell batteries and push each up under the ridge in the compartment with the "+" marking. Replace the cover. Manually turn on the device you want to control. Find the Code List that came with the remote.Control your Samsung TV with third-party remotes. Samsung remotes are designed to be convenient and useful, but we understand if you'd prefer to use a third-party remote, whether it's a universal remote, a game controller, or something else! Whether you are replacing a lost remote or using an alternative remote to help reduce clutter, a ...To Pair your LG TV with a compatible Universal remote, there a two steps to go about it; The first would require you to input the code manually while the other step, the right code, would be searched for automatically. Take the following steps for the pair up; MANUAL INPUT. Turn ON your TV. Press the SETUP button and afterwards, press and hold ...Step 4: Pairing the remote and the device. To program a universal remote control, you typically follow these steps: – Press and hold the device button that corresponds to the device you want to program, such as TV or DVD. – While holding down the button, enter the four or five-digit code for the device you want to program.Press the Magic button. Select the device mode. Press the number for your brand. Turn on your device. Press and hold the Magic button. Press the â Devicesâ button. Enter the code. One For All codes list. Frequently Asked Questions.Mar 12, 2020 ... Comments · Setup and Program this Terk 6 Device Universal Remote to Any Device! · Ematic AT103B Digital Converter Box + DVR Recording Tutorial &&...Press the 'Setup' button on your remote and hold it until the red LED lights up. Press the device (AUD, CBL, DVD, TV) type button and release. Enter the 4-digit code using the number keys and the LED will switch off. Now point the remote to your device and see if all the buttons are working.5 Digit Codes. 22563. The instructions included with your universal remote will usually have you press a button (or series of buttons) and then ask for a code. If you still need help, click here to reach out to our Customer Support Team. We're here to ensure you enjoy a seamless viewing experience on your TV!In fact, if you own a universal remote, then you might not even need to program it to work with your PS5. If your remote works with your TV, it'll most likely work with your PS5.Enter the code. Use the numeric keys to enter one of the codes from the tables above. If the code is correct, the LED on the remote will turn off, and the keys will work. If the code is incorrect, the LED on the remote will blink 5 times. If that happens, you'll have to repeat the process but enter a different code this time.The Smart 8 remote also has a Smart App to program your remote by pairing it to bluetooth. Simply select the devices you want to control in the app (Anroid and iOS) and the codes are sent to your remote. ... satellite cable and streaming players offers versatility. This TERK universal rechargeable remote provides up to 6 months of operation on ...Program your Gateway TV remote · Press and hold the MENU and OK buttons until the POWER button flashes twice, and then release both buttons · Enter in code 9 – 9 ...In the auto search method, all the universal remote codes are gone through scanning process in the remote. It scans one code at a time to find out the correct remote code that works with your remote to program the control. Follow the instructions given below: “Switch On” the smart device like “TV” that you want the universal remote …Wait until the power button comes on, and then release both the buttons. Now point out the remote control at the TV or to another device, press the Power button on the remote control and wait for 2 seconds. Suppose, if the power on your tv or device has been turned off then the remote has found the correct code.Universal remotes can be connected with major brands, including Sony. These remotes can be paired with several different devices, allowing you to control everything using one remote. Setting up a universal remote is also pretty easy, but that is only if you have the correct Sony TV universal remote codes.Next, power on your Vizio TV manually. Then, aim your remote at it and press the 'Volume Up' button. The TV will then go through the last set of codes. If the Vizio turns off, press the TV button to lock the code. If the Vizio TV does not turn off, press the 'Volume Up' button and keep pressing it every 3 seconds until the TV turns off.In the auto search method, all lg universal remote codes are gone through scanning process in the remote. It scans one code at a time to find out the correct lg remote code that works with your remote to program the control. Follow the instructions given below: “Switch On” the smart device like “TV” that you want the universal remote to ...3. Verifying the Programming: After entering the manufacturer code, test the remote's functionality by pressing the designated DVD control buttons, such as play, pause, stop, and eject. Observe the DVD player's response to these commands, ensuring that the remote effectively communicates with and controls the device.A: Answer. If you look at the row of the three buttons above the number pad. The one to the far right, next to the "Home" key. That should act as the back key. Answered 3 months ago by theinspector069. Helpful ( 0) Unhelpful ( 0) Report.First, turn your Polk Soundbar on. In your universal remote control, locate and choose the "Setup" button. Press and then hold the button so that the light turns red. Stop holding the setup button after the light is lit up. This will enable the remote to go into "Setup mode.". Press and release the button, then register your Polk soundbar.Enter the code. Next, enter the code for the device that you found. The 'Input' button will blink twice to confirm that the code has been set. To find the code for your device, you can check out our list above. And for more codes, visit the Spectrum website. Step. Here comes the Terk Universal remote control. The Terk Universal Remote 4-device model is what I am going to review here. First, the Terk remote dispenses with the batteries and is charged via a USB cable. For me that is a convenience since you no longer need batteries for the remote to operate. Step 1: Go to the RCA Accessories website. Step 2: Open up the battery panel on the back of your universal remote. Step 3: Find the paper sticker on the back of the battery panel. Enter the given ...Start by turning on the device you want to control, and then press the "Program" or "Code Search" button on the remote. The indicator light should turn on. Next, enter the code for your device using the number keypad on the remote. If the code is entered correctly, the indicator light will turn off.Press and hold the "Setup" button on your Pavy remote until the red light blinks twice. Enter the code 9-9-1, and the red light will blink twice again. Aim the remote at the device, and then press down and release the "Power" button. Press "Channel Up" or "Channel Down" repeatedly until your device turns off.Step 3: Enter Code (Code Entry Method) After selecting the device key, press and hold the "SETUP" key on the ONN remote until the LED under the device key blinks twice. Enter the four-digit ... Turn on the device you want to program. Press the “TV” button on your Terk universal remote. Hold down the “Setup button” on the remote until it flashes a light (indicating it’s in “Learning mode”). Enter the specific “Keycode” you obtained from the programming guide (usually found in the Instructions Booklet). As of September 2014, RCA has a universal remote code page online. Input information about the specific RCA universal remote to generate programming codes by product type. The page...The Terk - Rechargeable 8-Device Backlit Universal Remote (model TKTC8GB) supports a wide range of brands and models of devices. I was eager to consolidate all of the devices in the family room and store the collection of remotes that live on the table. Some of those devices are admittedly getting old.Video tutorial on how to setup and program in your device on this Terk 6 Device Universal remote. By anything, I mean what it's designed to do! If you've l...Turn on the LG TV you wish to operate with the remote control. Press and hold the SETUP button until the red light blinks twice, then release. Enter the three-digit code for your TV using the number buttons on the remote control. The red light will blink twice after each number you enter. After you have entered the code, press and release the ...May 19, 2023 ... Performing an automatic code search · Press TV once (or the desired device). · Press and hold SETUP until the TV button blinks twice. · Enter ...Its a code in manual which forces the remote into the search mode. First of all “Turn The Device On”. Now press and hold the “Setup” button. Enter the “9-9-1” (three digit) code. Now hold down the “Power Button” on the remote and then press the Channel up them until the device in this case your tv “Turns Off”.In the auto search method, all the universal remote codes are gone through scanning process in the remote. It scans one code at a time to find out the correct remote code that works with your remote to program the control. Follow the instructions given below: "Switch On" the smart device like "TV" that you want the universal remote to ...About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket Press Copyright ...5 Digit Codes. 22563. The instructions included with your universal remote will usually have you press a button (or series of buttons) and then ask for a code. If you still need help, click here to reach out to our Customer Support Team. We're here to ensure you enjoy a seamless viewing experience on your TV!Hey, how are you doing? Are you looking for Terk Universal Remote Codes? Do you want to know how to program Terk universal remote for your…Method #1. In programming your universal remote without a code, you'll need to: Hold down the SET and Zero (0) buttons on your universal remote four times at the same time. This step is crucial, and this part is where most people fail. You'll then notice the LED light indicator (usually red) turns on steadily. Press the ON button ... 1.6 Universal Remote Codes For Cable Box & Dvr; 1.7 Universal Remote Codes For Satellite Box & Dvr; 1.8 Universal Remote Codes For Dvd & Blu-ray Player; 1.9 Universal Remote Codes For CD Player; 1.10 Universal Remote Codes For Vcr; 1.11 Universal Remote Codes For Misc Audio Aux; 1.12 How To Program A Universal Remote? To program the Sharper Image Jumbo Universal Remote, first, locate the code for your device in the manual. Then, press and hold the "Code Search" button until the indicator light comes on. Enter the code for your device and press the power button to test. If it works, the light will turn off.Now point your remote towards your device and enter 3 Digit code for your brand of device. If the code is correct, your device will turn OFF. Now press the Power Button to turn ON the device and check by using VOL+ or VOL- buttons. If still your device is not working then retry the procedure with another code.How to Program Terk Universal Remote Codes [2023]Link: https://universalremotecodeslist.com/terk-universal-remote-codes-for-all-devices/Here are the steps to manually program the Zenith Universal Remote Control. First, turn the device on. Press the device (TV, Blu-ray, CBL-SAT, etc) button on your remote. Press and hold the SETUP button on your universal remote until the red light flashes. Now enter the Universal Remote Code for that device.By that, now you got until proceed to program the selected code from the directory what is shared below. Them might be thinking about the programming start. Afterwards let me tell you that you just need to enter the 4-digit code with the help of the Terk Versatile Detached Codes and the treat is virtually completed.Locate the power button on the blinds remote. It is typically labeled with a power symbol or "ON/OFF". Press and hold the power button for a few seconds until you see the LCD screen light up or any other indication that the remote is powered on. Release the power button once the remote is powered on.Press and hold the " Setup " button on your universal remote until the button blinks twice. Enter the code 991 into your remote. The button should blink twice again. Press and release the " Power " button on your remote. Point the remote at your device and press and hold the " Channel Up " button until your TV turns off.Most standard Roku remotes have four buttons to quickly access your favorite streaming apps. This replacement Roku remote has a grand total of 12 (Netflix, Amazon Prime Video, Roku Channel ...Auto Code Search: Press and hold the "TV" button on the QFX Universal Remote. The indicator light will illuminate, indicating that the remote is ready to be programmed for the TV. Next, press and hold the "Power" button while pointing the remote at the TV.Hey, how are you doing? Are you looking for Terk Universal Remote Codes? Do you want to know how to program Terk universal remote for your…2 CONTENTS Universal Remote Device Codes TV..... 3How To Program A Universal Remote? There are three simple ways to set up or configure a universal remote and the first one is Using a Keycode, Programming Via Universal Remote Code Search, and Manual Setup. Keycode. The universal remote may be readily programmed using the keycode, which also serves to identify the make and model of …Program your universal remote control to a SONY Sound Bar. Use the following 4 and 5 digit remote codes. SONY Sound Bar 4 Digit Remote Control Codes:4029 SONY Sound Bar 5 Digit Remote Control Codes:317593217230766 All codes reported working with the SONY Soundbar HT-CT60, HT-CT260, Sony STR-K700, Sony HTCT260, HTCT660, Sony CT-660, Sony CT770, SA-CT60, HT-CT260H, and HT CT150.Its a code in manual which forces the remote into the search mode. First of all "Turn The Device On". Now press and hold the "Setup" button. Enter the "9-9-1" (three digit) code. Now hold down the "Power Button" on the remote and then press the Channel up them until the device in this case your tv "Turns Off".Oct 23, 2022 ... Comments4 ; Setup and Program this Terk 6 Device Universal Remote to Any Device! Take a Bath Productions · 88K views ; Quickly Program This RCA ...Shop for terk universal remote control 4 device at Best Buy. Find low everyday prices and buy online for delivery or in-store pick-upThe Sofabaton U1 Universal Remote is a great pick for Element TV users that also want to use their remote control to control other devices. 3. Inteset 4-in-1 Universal Backlit Remote - Best for Streaming Services. The Inteset 4-in-1 Universal Backlit remote has all the bells and whistles you could ask for in an Element TV remote control.TERK ADVANTAGE. Benefits of using a Terk Antenna; Setup Is Easy; ... 6-Device Universal Remote. $24.99---- VIEW DETAILS ----TKRTBL08B. 8-Device Universal Remote. $29.99To program a universal remote to a Toshiba TV, find the TV code in the remote's manual or online. Then, follow the remote's instructions to input the code and sync it with your TV. Step 3: Program the Universal Remote. With the remote control code for your Toshiba TV in hand, it's time to program your universal remote to communicate with ...Welcome to the world of universal remote programming, where convenience meets confusion, right? In this friendly guide, we’re going to … Read more. Onn Soundbar Remote Codes. by Rameen. If you have an Onn Soundbar and need an Onn Soundbar universal remote code to program your player, The codes …How to Connect a Universal Remote to Your Projector Properly. Top Three Recommended Universal Remotes for Projectors. 1. SMK-Link Universal Projector Remote Control. 2. EWO’S Universal Projector Remote Control for Epson Projectors. …Web the #1 universal tv remote control app for smart & ir tvs in over 100 countries. Web · july 26, 2020 the 6 best tv remote apps to control your tv with your phone ever wanted to catch up on your favorite tv show, only to realize that the remote control is. Web remote controls can sometimes lose their programming when you change the batteries.Oct 23, 2022 ... Comments4 ; Setup and Program this Terk 6 Device Universal Remote to Any Device! Take a Bath Productions · 88K views ; Quickly Program This RCA ...Repeat Step 2 and Step 3 for each additional device. Turn on the device you want to program and locate the code list for your GE CL3 Universal Remote. Enter the programming mode by following Step 4. Using the number keypad on your remote, enter the device code for the additional device according to the code list.TERK ADVANTAGE. Benefits of using a Terk Antenna; ... Remote Program Videos. Need to Find Your Remote Revision Number?Find the codes you need to program your remote control. Remote control codes and instructions on how to program your Sony® remote control will vary by model. By clicking on the link below, you will be able to enter the model number of your remote and find the model-specific information that you need to program the remote:A: Answer. If you look at the row of the three buttons above the number pad. The one to the far right, next to the "Home" key. That should act as the back key. Answered 3 months ago by theinspector069. Helpful ( 0) Unhelpful ( 0) Report.Quick Answer. The Dynex remote can be programmed with and without code. If you have the right code, you can – Power on TV (or other device) > Press ‘Comp’ and ‘Enter’ button simultaneously > input the code > test the code > press the TV (or other device button) to save the code. For convenience, we have listed Dynex remote codes in ...RCA DTA800 TV/Converter Box Remote Control PN: DTA800B1. Watch on. Yes, a universal remote can work with a converter box. For it to be properly set up, the appropriate code needs to be entered into the remote. Depending on the make and model of the remote and the converter box, the code entry process may differ, so consulting the user manual of ...You will need the Terk universal remote codes to program your remote to any electronic device. This post has listed the Terk universal remote codes fork best popular far brands. Find the code that matches your TV brand plus proceed into use the cipher to run your remote. On this later part of this post is the guide on how the run ...Mar 27, 2024 · Press the Magic button. Select the device mode. Press the number for your brand. Turn on your device. Press and hold the Magic button. Press the â Devicesâ button. Enter the code. One For All codes list. Frequently Asked Questions. With the ability to connect to popular streaming boxes as well as major device brands, this remote consolidates all your controllers into one. The intuitive device setup of this Terk ultra slim eight-device universal remote control lets you search by brand, manual or direct code. See all Remote Controls. $19.99.First, turn your Polk Soundbar on. In your universal remote control, locate and choose the “Setup” button. Press and then hold the button so that the light turns red. Stop holding the setup button after the light is lit up. This will enable the remote to go into “Setup mode.”. Press and release the button, then register your Polk soundbar.Shop for terk universal remote control 4 device at Best Buy. Find low everyday prices and buy online for delivery or in-store pick-upQuick video tutorial showing you how to use just about any Remote control with Amazon Fire Stick. You can use your TVs factory remote, or a universal remote...How to pair universal remote to LG TV. The programming process is straightforward, regardless of whether you have a GE, RCA, Philips, Brightstar, or another brand of universal remote. This manual approach to programming your universal remote is a bit of a longer moethod but can help you et your LG TV and remote connected.Universal remote 4 digit codes will work with your Sceptre TV. 0991. 0000. 0080. NOTE: If you have the rc64 remote, try codes 10878, 11217, 11360, and 11599. Codes listed with an asterisk (*) are possible alternate codes for your TV. These alternate codes should operate the primary functions of your device in most cases (Power, Volume Up and ...To allow the universal remote to learn the various commands, press the TV device button on the universal remote and activate its learning mode. If there isn't a dedicated learning button, you ...Programming Your Universal Remote. Programming a universal remote may seem daunting at first, but with the right approach, it can be a straightforward and rewarding process. The first step is to identify the specific codes that correspond to the devices you want to control with your universal remote.These codes serve as the key to synchronizing the remote with your specific devices. Step 3: Enter Programming Mode. With the necessary information and code lists at your disposal, it's time to enter the programming mode on the One For All Universal Remote.It should look something like "714543-xxxx". The first six numbers remain the same; the last four are what you need to look for. If the last four digits end with "20", like "714543-8020", then your remote will accept the 4-digit code. On the other hand, if the last four digits end with "30", like "714543-8030", your Bose ...Feb 18, 2024 · 2. Input the Programming Code: Once in the programming mode, use the remote’s keypad or navigation buttons to input the programming code corresponding to your Sceptre TV. Carefully enter the code, ensuring accuracy and precision to avoid potential setup issues. Smart homes, home theaters and entertainment systems — with all of the different remote-controlled devices on the market today, remotes are increasingly cluttering up our living sp...On this video we will program a universal remote control to work with a TV this procedure is the same for any device supported by remote. I will take a scree...Point your universal remote at the soundbar you want to pair to. Press the Setup button on your universal remote until the light flashes (this step varies by brand), or press the AUX and OK buttons simultaneously, then press the channel up button. Hold until the soundbar turns off, then press the AUX button again to save (if successful, setup ...

Whether you've lost your original remote, inherited an old TV, disc player, or receiver that is missing its remote, or just want to de-clutter your living room, the Terk rechargeable 6-device universal remote is a very reasonably priced, though somewhat basic, remote control that does a lot of what it needs to without much in the way of fuss or programming difficulties.. Cinepolis inglewood movies

how to program terk universal remote

Best overall. 1. SofaBaton X1. View at Amazon. View at Newegg. Best overall. The SofaBaton X1 lets you control the greatest number of devices, and works with Alexa and Google Assistant. Read more ...The lack of intuitive programming instructions and convoluted setup process may deter less tech-savvy individuals from fully utilizing the remote's potential. 3. Limited Device Compatibility: While the TERK remote boasts six-device control capability, it doesn't always work flawlessly with every device. Features. Manage up to four electronic devices with this TERK universal rechargeable remote. A fully-backlit keypad enables easy use in the dark, while the quick-access keys let you seamlessly access your favorite apps. Compatibility with most TVs, satellite cable and streaming players offers versatility. This TERK universal rechargeable remote ... These codes serve as the key to synchronizing the remote with your specific devices. Step 3: Enter Programming Mode. With the necessary information and code lists at your disposal, it's time to enter the programming mode on the One For All Universal Remote.To program a RCA Universal Remote with codes, first find the code for your device in the remote's manual or online. Then, press and hold the device button on the remote, enter the code, and release the button. Test the remote to see if it works with your device.Video tutorial on how to setup and program in your device on this Terk 6 Device Universal remote. By anything, I mean what it's designed to do! If you've l...How to program a universal remote to work with your Sceptre TV using a code. The first method is using a keycode. With the correct code, you can program the universal remote to work with your Sceptre TV. The keycode identifies the brand and model of your device. The first step is to turn the Sceptre TV you want to configure ON.The Sofabaton U1 Universal Remote is a great pick for Element TV users that also want to use their remote control to control other devices. 3. Inteset 4-in-1 Universal Backlit Remote - Best for Streaming Services. The Inteset 4-in-1 Universal Backlit remote has all the bells and whistles you could ask for in an Element TV remote control.Step 2: Initializing the Remote Control. After setting up the fan receiver, the next step in programming your Harbor Breeze fan remote is to initialize or sync the remote control with the receiver. This process establishes a connection between the two, enabling the remote control to communicate with the fan.Are you struggling to program your Dish remote? Don’t worry, we’re here to help. Programming a Dish remote may seem daunting at first, but with our step-by-step guide, you’ll be ab...Tutorial on how to program and setup Philips universal remote SRP9488C/27 with TV, STR, BLU RAY, AUD, DVD, CBL, SAT and AUX without any codes. For Direct Cod...The first method is using a keycode. With the correct code, you can program the universal remote to work with your Ocosmo TV. The keycode identifies the brand and model of your device. The first step is to turn the Ocosmo TV you want to configure ON. Then we press the TV button on your Universal Remote. Next, we need to press and hold the SETUP ...How to program your Logitech Harmony remote. To control your Roku TV system with your Logitech Harmony remote, follow the steps listed on the Logitech support site. When prompted, enter the name of the manufacturer (e.g., Hisense, Insignia, Sharp, or TCL) and then enter “Roku TV” in the Model Number field. Last updated on 3/19/2024, …Turn on the device you wish to control (TV, VCR, DVD, DVR, satellite receiver, or cable box). Locate the Brand Code (s) from the list provided with your remote. Press and hold the Device button you wish to program. (TV, DVD, Aux, etc.) When the LED for that button turns on and remains on, keep holding down that button.Turn on your TV or another device you wish to control. Press and hold the corresponding Device and Power buttons on the remote at the same time. Wait until the power button comes on, and then release both buttons. Pointing the remote at the TV or another device, press the Power button on the remote and wait 2 seconds.Power on the device you want to control. For example, if you want to use your GE remote to program your TV, turn on the TV now. 2. Press and hold down the Setup button until the red light comes on. The light is usually at the top of the remote or on the power button. Release your finger once the red light is visible.Quick Answer. You can program the RCA universal remote with and without codes. If you have the code, power on selected device > press and hold the device key (TV, DVD, or your selected device) > enter the code while holding down the button > if the power button lights up the remote is programmed. If not, try a different code and repeat the process.Especially for Samsung remote Model:BN59-01199F,AA59-00666A,AA59-00741A. including smart hub buttons. 2.Farther transmitting distance, stable performance. Replaces your damage or old one and covers the all functions of the original remote. 3.Simple universal remote，small and compact size makes this remote control easy to grip and uneasy to slip..

Popular Topics